Most plumbing problems are a fixture, a valve or a single run. A repipe is different: it is the decision that the supply piping throughout the house has reached the end of its life and that replacing it costs less over the next decade than continuing to repair it.
Two materials bring Central Ohio homeowners to that decision more than anything else, and they fail in completely different ways.
Galvanized steel, and why pressure drops
Galvanized steel supply pipe was standard in houses built through roughly the 1950s and into the 1960s. It is steel with a zinc coating, and the zinc is what was supposed to keep it from rusting.
The zinc wears away from the inside over decades. Once it is gone, the steel beneath corrodes, and the corrosion products build up on the interior wall of the pipe. The passage narrows from the inside while the outside of the pipe looks perfectly sound.
That produces a specific and recognizable pattern:
- Water pressure that has declined gradually over years rather than dropping suddenly.
- Hot water pressure noticeably worse than cold, because heat accelerates the process.
- Brown or rust tinted water, especially first thing in the morning or after the house has been empty.
- Pressure that falls off sharply when a second fixture is opened.
- Pinhole leaks appearing at threaded joints, which is where the wall is thinnest.
The pattern matters because none of it is fixed by replacing one section. Cutting out a corroded run and splicing in new pipe restores flow in that section and leaves the rest of the system exactly as it was, which is why galvanized repairs tend to be followed by more galvanized repairs.
Polybutylene, and why it fails without warning
Polybutylene is a gray plastic supply pipe installed widely from roughly the late 1970s into the mid 1990s. It is a different problem entirely.
Rather than narrowing gradually, polybutylene can become brittle and fail at or near fittings, often without any prior symptom. There is no pressure warning, no discoloration, no slow decline. The first sign is frequently water.
Identifying it is straightforward when the pipe is visible. It is gray, usually flexible, and typically stamped with “PB” and a code along its length. It is most often seen at the water heater, at the main shutoff, and running through an unfinished basement or crawl space.
Two cautions. Gray plastic pipe is not automatically polybutylene, and polybutylene was also used underground for water service lines, so a house can have it outside without having it inside. A plumber identifies it from the markings rather than the color.
Insurers in some cases ask about it, and it comes up at inspection. That is worth knowing before a sale rather than during one.
What goes in instead
Two materials do the overwhelming majority of residential repipes, and both are good. The honest answer is that the choice matters less than the quality of the installation.
Copper is rigid, long established and widely trusted. It tolerates heat well, it is not affected by sunlight, and it can be repaired by any plumber anywhere. It costs more in both material and labor because every joint is soldered or pressed and every run is cut and fitted to the house. In Central Ohio water chemistry it performs well, though very aggressive water can pit it over a long period.
PEX is flexible cross linked polyethylene. Its practical advantages in a retrofit are substantial: it snakes through existing wall and joist cavities with far less demolition, it has fewer joints because a run can be continuous from a manifold to a fixture, and it tolerates a freeze better than rigid pipe because it can expand somewhat before it splits. It installs faster, which is most of why it costs less. It is damaged by ultraviolet light, so it is not for exposed exterior use, and it needs appropriate protection where it passes through framing.
There is also a layout decision that comes with PEX. A home run manifold, where each fixture has its own line from a central manifold, gives you individual shutoffs and very consistent pressure. A trunk and branch layout mirrors traditional piping with fewer total feet of pipe. Both are legitimate; the manifold costs more and buys control.
What a repipe actually involves
This is the part people want to know and rarely get described honestly.
Access. The plumber has to reach every run. In a house with an unfinished basement and accessible walls that is comparatively easy. In a finished basement with a drywalled ceiling, or in a two story house where lines run up interior walls, it means opening walls and ceilings at specific points. A good plumber plans those openings deliberately, in the least disruptive places, rather than cutting wherever is convenient.
Drywall repair. This is a real line item and it is where quotes diverge most. Ask explicitly whether the quote includes patching, finishing and painting, or whether it stops at a hole in the wall. Both are legitimate scopes. Only one of them leaves you with a finished house.
Water off. The house is without water for part of the work. On a typical single family repipe that is usually measured in days rather than weeks, and a plumber who sequences well can often restore service at the end of each day.
Inspection. Repiping is permitted work and it is pressure tested and inspected before it is closed up. That is a schedule dependency and it is also your protection.
Reconnection at every fixture. New supply lines terminate at every fixture, and old shutoff valves are usually replaced at the same time because a valve of that age will not reliably close anyway.
When a repipe is the right call and when it is not
A repipe is right when the material itself has failed as a system: galvanized that has narrowed throughout, polybutylene anywhere in the house, or a system that has produced several leaks in different places within a few years.
It is not right when the problem is a pressure regulator, a single corroded run, a water heater, or water chemistry that a treatment system would address. A plumber who recommends a full repipe without first establishing what is actually happening has skipped the diagnosis.
A useful intermediate step exists. Replacing the most problematic runs, the main line and the hot water distribution, while leaving sound sections in place, is a legitimate phased approach in some houses. It is not a half measure if it is chosen deliberately with a plan for the rest.
Doing it during a remodel
If a kitchen, bathroom or basement project is already opening walls, that is the cheapest moment in the life of the house to repipe. The demolition and the drywall repair are already in the budget.
That timing argument is worth raising at the design stage of any remodel in a house of the relevant age, because the chance does not come around often.
What belongs in the quote
Six items make two quotes comparable: the material and layout, whether all supply piping is included or only part, how access will be gained and where walls will be opened, whether drywall repair and paint are included, whether fixture shutoff valves are being replaced, and whether the permit and inspection are in the price.
Our plumbing work across Columbus and the surrounding suburbs includes repiping, and the first step is always establishing what the piping actually is and what it is actually doing, because the material in the wall decides everything that follows.
Frequently asked questions
How do I know if my house has polybutylene pipe?
Look for gray flexible plastic supply pipe, usually stamped with “PB” and a code along its length, most often visible at the water heater, at the main shutoff and in an unfinished basement or crawl space. Gray plastic is not automatically polybutylene, so identification comes from the markings rather than the color. It was installed from roughly the late 1970s into the mid 1990s, and it can also appear underground on a water service line without being inside the house.
Why is my water pressure worse on hot than on cold?
In a house with galvanized steel supply piping that is a classic sign of interior corrosion, because heat accelerates the process and the hot side narrows faster. The passage closes from the inside while the pipe looks fine from the outside. Replacing a single section restores flow in that section only, which is why galvanized repairs tend to be followed by more of them.
Is PEX as good as copper?
Both are good materials and the quality of the installation matters more than the choice between them. Copper is rigid, long established and repairable anywhere. PEX is flexible, which in a retrofit means far less demolition, fewer joints and better tolerance of a freeze, and it installs faster, which is most of why it costs less. PEX is damaged by ultraviolet light so it is not used exposed outdoors.
How long does a whole house repipe take?
On a typical single family home it is usually measured in days rather than weeks, and the house is without water for part of that. A plumber who sequences the work well can often restore service at the end of each working day. The schedule also depends on the inspection, since the new piping is pressure tested and inspected before anything is closed up.
Does a repipe quote include fixing the walls?
That depends entirely on the quote, and it is the item that most often explains why two numbers differ. Some plumbers price the piping and leave the openings for someone else; others include patching, finishing and paint. Both scopes are legitimate. Ask the question directly before comparing totals, because one quote may be leaving you with a finished house and the other with a list of holes.