A large share of Columbus’s older housing, particularly in the neighborhoods built before the Second World War, is heated by water rather than by air. There are radiators under the windows, or baseboard along the wall, and there is a boiler in the basement rather than a furnace.
Owners of these houses get told two things that are frequently wrong: that the system is obsolete, and that it should be ripped out and replaced with forced air. Neither is automatically true, and the second one is an expensive mistake when the existing system is sound.
Here is how these systems actually work, what goes wrong with them, and how to decide what to do. The short version is that the distribution usually outlasts the boiler, which changes the whole economics of the decision.
Two different systems that look similar
Hot water, or hydronic. A boiler heats water to well below boiling and a circulator pump moves it through pipes to radiators or baseboard. The water gives up its heat and returns to the boiler. The system is closed and under modest pressure.
Steam. An older design, and still common in houses from the early twentieth century. The boiler boils water, steam rises through the piping by its own pressure, condenses in the radiators and returns as water by gravity. There is no circulator pump on a classic one pipe steam system.
Telling them apart matters because they are diagnosed and serviced completely differently. A steam radiator has an air vent on its side, often a small brass cylinder. A hot water radiator has a bleed valve at the top instead. A steam boiler has a sight glass showing the water level; a hot water boiler has a pressure gauge and an expansion tank.
If someone proposes work on your system without knowing which one you have, that is the end of the conversation. The two are diagnosed differently, serviced differently and fail differently, and a technician who has not established which is in front of them is guessing.
Why people like them
There are real reasons these systems have survived in older houses, and they are not nostalgia. The performance characteristics suit the buildings they were installed in.
The heat is even and quiet. There is no fan noise and no draft, and radiant surfaces warm objects and people rather than blowing warm air around. In a house with high ceilings and leaky original windows, radiators under the windows do exactly what they were designed to do.
They also move no air, which means they do not distribute dust the way a forced air system does, and there is no ductwork taking up space in a house that was never designed to have any.
What actually goes wrong
Air in a hot water system. The most common complaint, and the easiest fix. A radiator cold at the top and warm at the bottom has air trapped in it. Bleeding it releases the air, and if the air comes back repeatedly there is a leak drawing it in or a problem with the expansion tank.
A waterlogged expansion tank. On a hot water system the expansion tank gives the water somewhere to go as it heats. When the tank fills with water it stops doing its job, system pressure climbs, and the relief valve starts discharging. Owners often see the discharge and assume the boiler is failing.
Steam system water level and the low water cutoff. The safety device that shuts the boiler down if the water level drops. It needs flushing on a schedule and it is a safety device rather than a maintenance nicety.
Steam vents. On a one pipe system each radiator has a vent that lets air out so steam can enter. A vent that has failed closed means a cold radiator; one that has failed open means steam escaping into the room. Vents are also how a steam system is balanced, so that the far radiator heats at the same time as the near one. Most of the “uneven heat” complaints on steam systems are a venting problem, not a boiler problem.
Circulator and zone valve failures on hot water systems, which produce one zone that does not heat while the rest of the house is fine.
Sediment, scale and corrosion inside the boiler and piping over decades, which reduces efficiency and eventually causes leaks.
Pipe insulation that was removed. On a steam system, uninsulated mains lose heat into the basement instead of delivering it upstairs, and the system runs longer to compensate.
Repair or replace
The honest version of this decision rests on four questions, and the order matters. Answering the fourth before the third is how people end up replacing a boiler and inheriting a venting problem.
Is the boiler itself leaking? A cracked section or a leaking heat exchanger is a replacement. A leaking fitting or valve is a repair.
What is its efficiency and age? Older atmospheric boilers are considerably less efficient than current equipment. A replacement can produce a real reduction in fuel use, which is the main financial argument for replacing something still working.
Is the distribution sound? This is the key question and it is frequently missed. The radiators and the piping typically outlast several boilers. If the distribution is in good condition, replacing only the boiler keeps the part of the system that is expensive to replace and is working well.
Is the venting compatible? A modern high efficiency boiler vents differently than an old atmospheric one, usually through a sidewall with plastic pipe rather than up the existing chimney. That has consequences for the chimney, which may have been serving the water heater as well.
That last point catches people. Removing a boiler from a shared masonry chimney can leave a water heater venting alone into a flue now far too large for it, which causes condensation and deterioration. Replacing the boiler and leaving the water heater on the old chimney is a decision that has to be made deliberately, not discovered afterwards.
Converting to forced air
This gets proposed more often than it should, and it is rarely as simple as it sounds. The cost is not just the new equipment.
A house built for radiators has no ductwork and usually no good path for it. Running supply and return ducts through a finished older home means soffits, closet chases, dropped ceilings and lost space, and it means giving up the even quiet heat the house currently has.
The usual reason for wanting it is air conditioning, and that is a reasonable goal with a better solution.
Adding cooling without losing the boiler
Three approaches work in a house with hydronic or steam heat, and none of them requires abandoning the existing system. Which one fits depends on the layout and on how much disruption you are willing to accept.
Ductless mini splits. Individual indoor units serving rooms or zones, with a small outdoor unit and only a small penetration through the wall. The least invasive option, and it also provides supplemental heat.
A high velocity small duct system. Flexible small diameter tubing that can be threaded through existing wall and joist cavities, with small outlets rather than conventional registers. More involved than mini splits and more discreet in the room.
A conventional ducted system for cooling only, where the house has an attic or a layout that allows it.
Whichever applies, keeping the boiler means the heating system that works for the house stays, and the cooling problem gets solved on its own terms. That is almost always the cheaper and less invasive outcome.
Maintenance that actually matters
For a hot water system: an annual service, checking system pressure, confirming the expansion tank is functioning, bleeding radiators at the start of the season, and verifying the relief valve.
For a steam system: an annual service, flushing the low water cutoff on the schedule the manufacturer specifies, checking and balancing the radiator vents, confirming the water level and the sight glass, and keeping the main piping insulated.
For both: the combustion side needs the same attention as any gas appliance, meaning the burner, the flue and the draft. That part is a safety item rather than an efficiency one.
Our HVAC crews work on both hydronic and steam systems across Columbus and the surrounding suburbs. On a house of that era the first visit is usually diagnosis rather than a quote, because a cold radiator has half a dozen causes and only one of them is the boiler.
Frequently asked questions
How do I know if I have a steam or hot water system?
Look at a radiator. A steam radiator has an air vent on its side, often a small brass cylinder, and no valve at the top. A hot water radiator has a bleed valve at the top instead. At the boiler, a steam system has a sight glass showing the water level, while a hot water system has a pressure gauge and an expansion tank. The two are serviced completely differently, so it is the first thing any technician should establish.
Why is one radiator cold when the rest of the house is warm?
On a hot water system the usual cause is air trapped at the top of that radiator, which bleeding will release; if it returns repeatedly there is a leak or an expansion tank problem drawing air in. On a one pipe steam system it is almost always a failed air vent on that radiator, since the vent has to let air out before steam can enter. Neither is a boiler failure.
Should I replace my old boiler with a furnace?
Usually not, and the question behind it is normally air conditioning rather than heating. A house built for radiators has no ductwork and no good path for it, so converting means soffits, chases and lost space, and it gives up the even, quiet heat the house already has. Ductless mini splits or a high velocity small duct system add cooling without touching the heating system.
Can I keep my radiators and replace just the boiler?
Yes, and it is frequently the right answer. The radiators and the distribution piping typically outlast several boilers, and they are the expensive part to replace. The item to resolve during planning is venting: a modern high efficiency boiler usually vents through a sidewall rather than the chimney, which affects anything else that was sharing that flue, most often the water heater.
Why is water discharging from the pipe near my boiler?
On a hot water system that is usually the pressure relief valve doing its job because system pressure has climbed, and the most common reason is an expansion tank that has waterlogged and stopped absorbing expansion. The valve is a safety device and the discharge is a symptom rather than the fault. It should be diagnosed promptly rather than ignored, and the relief valve should never be capped or plugged.